Motor-Driven UniSlide® MA60 Series
The MA60 Series UniSlide stage has a body width of 6 inches, slider length of 6 inches carrying a 200 lbs. horizontal load.
The MA60 Series UniSlide stage has a body width of 6 inches, slider length of 6 inches carrying a 200 lbs. horizontal load. . The MA60 can travel up to 41″ with the 6″ slider/carriage. The MA60 Series UniSlide is available in 7 lead screw pitches. Recommended step rate is 1000/steps per second. The MA60 is versatile for a variety of applications.
MA60 Series UniSlides are comprised of an aluminum alloy extruded dovetail base with 60 degree opposing V-type ways. An aluminum alloy carriage that runs in the dovetail ways of the base. Lead screws are constrained and supported with steel thrust bearings and snap ring retainer. The lead screw drive nut is a tension adjustable nut made of Delrin providing low friction, and minimal backlash.
Features
Maximum Horizontal Load Capacity – 200 lbs. (90.7 kg.)
Maximum Vertical Load Capacity – 40 lbs. (18.14 kg.)
Maximum Travel Distance – 41″ (104.2 cm)
Specifications
Factors such as size of the motor, size of the payload, travel distance, mounting direction/plane, etc. effect the actual capability of any assembly. Please contact Velmex Application Engineers to configure a system that will meet your exact requirements.
| Operating temperature | 0 to 180° F (-18 to 82° C) |
Properties of Velmex Stages - Information on stage composition, tolerances, wear and design for specialty applications.
Load Parameters - Definitions and parameters that effect the various load ratings.
UniSlide® MA60 Dimensions
| Standard | Metric | |
| Travel Distance | 2" - 41" | 5.08 – 104.14 cm |
| Base Length | 9" - 48" | 22.86 – 121.92 cm |
| Slider Length | 6" | 15.24 cm |
| Weight | 6.6 – 27.7 lbs. | 2.99 – 12.56 kg. |
| Height** | 1.75" | 4.45 cm |
| Width | 6" | 15.24 cm |
† Motors sold separately.
** Deeper “B” base configurations available.
‡ Standard travel distances available are in 3″ increments.
UniSlide® MA60 Load Calculations
| Load Capacity | lbs. | kg. |
| Maximum Horizontal Load | 200 lbs. | 91 kg. |
| Load Normal (LN)* | 80 lbs. | 36.29 kg. |
| Load Thrust (LT)* | 40 lbs. | 18.14 kg. |
| Cantilever Side (LCS)* | 80 lb-in | 9.04 N-m |
| Cantilever Inline (LCI)* | 160 lb-in | 18.07 N-m |
* Normal Operating Loads are less than the maximum.
Lead Screw Specifications
| Repeatability | 0.00015″ (4 microns) typical |
| Straight line accuracy | 0.003″ (0.076 mm) over entire travel distance. Higher accuracy 0.0015″ (0.038mm) available |
| Screw lead accuracy | 0.003″/10″ (0.076 mm/25 cm) 0.0015″/10″ available. Consult factory. |
English Thread Lead Screws
| Pitch | Backlash Typical | Resolution | |||||||
| Turns per inch | Advance per revolution | English | Metric | Degrees | Standard Accuracy | Precision Accuracy | English | Efficiency | Lead Screw Diameter |
| 40 | 0.025" | 0.00013" | 0.003 mm | 1/200 rev or 1.8° | C | P40 | 0.0000625" | 0.14 | 1/2" |
| 20 | 0.05" | 0.00025" | 0.006 mm | 1/200 rev or 1.8° | B | P20 | 0.000125" | 0.26 | 1/2" |
| 10 | 0.1" | 0.0005" | 0.013 mm | 1/200 rev or 1.8° | W1 | P10 | 0.00025" | 046 | 1/2" |
| 5 | 0.2" | 0.001" | 0.025 mm | 1/200 rev or 1.8° | W2 | P5 | 0.0005" | 0.64 | 1/2" |
| 2.5 | 0.4" | 0.002" | 0.051 mm | 1/200 rev or 1.8° | W4 | P2.5 | 0.001" | 0.73 | 1/2" |
Metric Thread Lead Screws
| Pitch | Backlash Typical | Resolution | |||||||
| Turns per cm | Advance per revolution | English | Metric | Degrees | Standard Accuracy | Precision Accuracy | Metric | Efficiency | Lead Screw Diameter |
| 10 | 1 mm | 0.0002" | 0.005 mm | 1/200 rev or 1.8° | K1 | Q1 | 0.0025 mm | 0.15 | 14 mm |
| 5 | 2 mm | 0.00039" | 0.01 mm | 1/200 rev or 1.8° | K2 | Q2 | 0.005 mm | 0.33 | 14 mm |
Resolution specified with standard Velmex motor configurations with 1.8° step angles using VXC Stepping Motor Controller.
Options/Accessories for MA60 UniSlide®Assemblies
NEMA 23 VML231-3.0-D Motor
NEMA 23 Motor for UniSlide®, XSlide®, BiSlide® and B48 Series Rotary Stages
NEMA 23 VML232-4.0-D Motor
NEMA 23 Motor for UniSlide® BiSlide® and B48 Series Rotary Stages
NEMA 34 VML341-4.0-D Motor
Compatible with UniSlide®, BiSlide®, BiSlide® Parallel Coupled, and BiSlide® Belt Driven Assemblies
VXC™ Stepper Motor Controller
The new VXC is a plug and play microstepping motor controller / driver with the ability to run up to 4 axes simultaneously. This easy to setup bipolar controller has the ability to be run standalone, or be integrated into a system.
A6000TX Adapter Plate
A6000XY Adapter Plate
Mount an A60 or MA60 Series UniSlide to another A60 or MA60 Series or to an A40 or MA40 Series in XY.
A6000XZ Adapter Plate
To mount an A60 or MA60 Series UniSlide to another A60 or MA60 Series or to an A40 or MA40 Series in XZ. (The A60 or MA60 would be the base horizontal stage.)
A6001XZ Adapter Bracket
Mount an A60 or MA60 Series UniSlide to another A60 or MA60 Series (up to 12″) or to an A40 or MA40 Series (up to 12″) in XZ.
B5990TXZ-BK Adapter Plate
Use this bracket to mount two B5990TS Rotary Tables at right angles to each other or to mount a B5990TS to a UniSlide® Linear Stage.
B6003XZ Adapter Bracket
To mount an A60 or MA60 Series UniSlide to another A60 or MA60 Series (12″- 15″) or to an A40 or MA40 Series (12″- 15″) in XZ. (The A60 or MA60 would be the base horizontal stage.)
B6004XZ Adapter Bracket
To mount an A60 or MA60 Series UniSlide to another A60 or MA60 Series (over 15″) or to an A40 or MA40 Series (over 15″) in XZ. (The A60 or MA60 would be the base horizontal stage.)
B9000XY Adapter Plate
To mount a B90 or B90 Series UniSlide to another B90 or B90 Series or to an A60 or MA60 Series in XY. (The B90 or B90 would be the base stage.)
B9000XZ Adapter Plate
To mount a B90 or B90 Series UniSlide to another B90 or B90 Series or to an A60 or MA60 Series in XZ. (The B90 or B90 would be the base horizontal stage.)
B9001XZ Adapter Bracket
To mount a B90 or MB90 Series UniSlide to another B90 or MB90 Series (up to 18″) or to an A60 or MA60 Series (up to 18″) in XZ. (The B90 or MB90 would be the base horizontal stage.)
B9002XZ Adapter Bracket
To mount a B90 or MB90 Series UniSlide to another B90 or MB90 Series (over 24″) or to an A60 or MA60 Series (over 24″) in XZ. (The B90 or MB90 would be the base horizontal stage.)
B9003XZ Adapter Bracket
To mount an A60 or MA60 Series UniSlide to another A60 or MA60 Series (over 15″) or to an A40 or MA40 Series (over 15″) in XZ. (The A60 or MA60 would be the base horizontal stage.)
Encoder Cables
Encoders
T-slot Hinge
T-slot Mounting Flange
Tab 2 Remote Send Pendant
Tilt Base
VRO™ Encoder Readout
The Velmex VRO™ Encoder Readout is a compact one or two axes digital readout for linear and rotary incremental encoders.
B69 Platform Shelf
Platform shelf from UniSlide® A60 and MA60 Elevating Tables that can be used on vertical UniSlide® Assemblies.
Left-Right Screw Motion
This configuration enables two carriages to travel along a shared axis using a single lead screw while moving towards or away from each other.
Motorized / Manual Operation
Optional Finishes
Many Velmex Products come standard with a brushed aluminum finish. Optional finishes including Black Anodizing are available.
Slider Lengths
All UniSlide® Assemblies are available with a variety of carriage (slider) lengths to suit different application needs.
Two Independent Carriages
Separate and precise positioning along the same linear axis using two lead screws.
UniSlide® Way Covers
Way Covers protect the slider and dovetail base from dust, dirt and grit that could hamper the efficient operation of the slide, thereby extending the life of the slide.
UniSlide® Vacuum Modifications
Stages for use in vacuum environments can be customized with special materials, coatings, and seals to ensure compatibility with low-pressure conditions and minimize outgassing
Velmex offers a multitude of options and accessories for all its products. Usually an option or an accessory will address your requirements. When it doesn’t, we can make custom modifications, including:
• Additional holes or slots. (A drawing is required.)
• Intermediate plates to mount your payload
• Special or in between lengths of the dovetail base
• Lead screw shaft extensions
• Choice of drive nut materials, including brass and Vespel
We can also offer customized configurations to address special environmental and vacuum applications.
Applications and Examples
Note: the example displayed may be a custom configuration, designed to the customer’s specifications; and not offered as a standard product. Custom configurations could contain custom, externally-fabricated components.
Downloads
The majority of CAD drawings found in our Technical Library are Step (.stp) files. You will also see .dxf, .dwg, .sat and .pdf files. For .STP files, you may need to right click on the download button and save the “target” or “link”. If you require a different format or cannot located the drawing you require, please contact us.
| Title | Summary | File Type | Link | hf:file_type |
|---|---|---|---|---|
| MA6015xxx-S6.dwg | Series MA60, 8″ travel, | dwg | dwg | |
| Motorized UniSlide Dimensional Drawings.pdf | Dimensional drawings for the 5 Series of Motorized UniSlide Linear Stages | |||
| UniSlide® Users Manual | Operating and Service Manual for UniSlide® Stages |
Knowledge Base
| Motion | Linear |
|---|---|
| Maximum Travel | 80" (203.2 cm) |
| Minimum Travel | 5" (12.7 cm) |
